M5Stack · ESP32 · 0.96" · 80×160
M5Stack M5StickC specifications
This page collects the pinout, free GPIOs and hardware details of the M5Stack M5StickC. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
The first M5StickC has a 0.96-inch 80×160 screen on an ST7735S, which is small even by stick standards. Two short lines of text or a single gauge is about what fits. Everything else matches the later Plus closely: ESP32-PICO-D4 with 4 MB flash, AXP192 power chip, BM8563 clock, PDM microphone, IR transmitter and a red LED.
Pins are the same as on the Plus for the display (MOSI 15, CLK 13, DC 23, RST 18, CS 5), the I2C bus (21/22), the buttons (37, 39) and the microphone (0, 34). The original adds an interrupt line from the PMU and RTC on GPIO 35 and lacks the buzzer.
Check the IMU on older units. M5Stack replaced the SH200Q with an MPU6886 in August 2019, and the two need different drivers. The 95 mAh battery is smaller than the Plus's 120 mAh.

- Screen
- 0.96" · 80×160
- Chip
- ESP32
- Memory
- 4 MB flash, no PSRAM
- Input
- no touch
Key features
- 0.96-inch, 80×160, ST7735S
- ESP32-PICO-D4, 4 MB flash
- AXP192 PMU, BM8563 RTC
- MPU6886 IMU (SH200Q before 2019-08)
- Microphone, IR transmitter, red LED
- Grove port and HAT header
Specifications
| Manufacturer | M5Stack |
|---|---|
| Screen size | 0.96" |
| Resolution | 80×160 px |
| Colour depth | 16-bit |
| Display controller | ST7735S (SPI) |
| Display interface | SPI |
| Touch | None (2 buttons) |
| Microcontroller | ESP32 |
| Module | ESP32-PICO-D4 |
| CPU clock | 240 MHz |
| Internal SRAM | 520 KB |
| PSRAM | None |
| Flash | 4 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Since 2019-08 the IMU is an MPU6886 (earlier units: SH200Q). AXP192 PMU, BM8563 RTC, SPM1423 microphone, IR transmitter, 95 mAh battery. |
| Display | 80×160, ST7735S: MOSI 15, CLK 13, DC 23, RST 18, CS 5 |
| I2C | SDA 21, SCL 22, IRQ 35: IMU, PMU, RTC |
| Inputs | Button A GPIO 37, Button B GPIO 39 |
| Ports | Grove 32/33; HAT header 0, 26, 36 |
| Battery | 95 mAh |
| Size | 48.2 × 25.5 × 13.7 mm, 15.1 g |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | Microphone clock (also on the HAT header) |
| GPIO 5 | LCD CS |
| GPIO 9 | IR transmitter |
| GPIO 10 | Red LED |
| GPIO 13 | LCD SCK |
| GPIO 15 | LCD MOSI |
| GPIO 18 | LCD reset |
| GPIO 21 | I2C SDA (IMU, PMU, RTC) |
| GPIO 22 | I2C SCL (IMU, PMU, RTC) |
| GPIO 23 | LCD DC |
| GPIO 26 | HAT header GPIO |
| GPIO 32 | Grove port (yellow) |
| GPIO 33 | Grove port (white) |
| GPIO 34 | Microphone data |
| GPIO 35 | PMU / RTC interrupt |
| GPIO 36 | HAT header GPIO (input only) |
| GPIO 37 | Button A |
| GPIO 39 | Button B |
Source: github.com, docs.m5stack.com, docs.m5stack.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 26 | GPIO, PWM | On the HAT header |
| GPIO 32 | GPIO, PWM, ADC | Grove port (yellow) |
| GPIO 33 | GPIO, PWM, ADC | Grove port (white) |
| GPIO 36 | GPIO, ADC | On the HAT header, input only |
- Grove port — GPIO 32, 33 · HY2.0-4P
- HAT header — GPIO 0, 26, 36 · 8-pin female
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- 80×160 is tiny. Design for icons and short numbers.
- GPIO 0 on the HAT header is also the microphone clock.
What it is good for
- •IR remotes
- •Step and motion counters
- •Minimal status badges
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | M5StickC |
|---|
Board package: M5Stack board package (Boards Manager: M5Stack)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which IMU does my M5StickC have?
Units made after August 2019 have an MPU6886; earlier ones have an SH200Q.
What is the display resolution of the original M5StickC?
80×160 pixels on a 0.96-inch ST7735S.
Which pins are free?
GPIO 32/33 on the Grove port and GPIO 26 and 36 on the HAT header (36 is input-only).
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the M5Stack family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.