M5Stack · ESP32-S3 · 0.85" · 128×128
M5Stack AtomS3R specifications
This page collects the pinout, free GPIOs and hardware details of the M5Stack AtomS3R. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
The headline difference from the AtomS3 is memory: the AtomS3R uses an ESP32-S3-PICO-1-N8R8 with 8 MB of flash and 8 MB of PSRAM in a 24 × 24 mm cube that weighs under 7 grams. The front is a 0.85-inch 128×128 IPS screen that doubles as the user button.
One recent change: M5Stack switched the display controller from GC9107 to ST7735 in May 2026. The pins stayed the same (MOSI 21, SCK 15, DC 42, CS 14, reset 48), but your driver has to match the panel. The backlight isn't on a GPIO at all; an LP5562 LED driver on the internal I2C bus (SDA 45, SCL 0) sets it.
Also on that bus are a BMI270 IMU at 0x68 and, behind it, a BMM150 magnetometer. An IR transmitter sits on GPIO 47. For wiring there's a Grove port on GPIO 2 and 1 and six pads on the bottom (5, 6, 7, 8, 38, 39).

- Screen
- 0.85" · 128×128
- Chip
- ESP32-S3
- Memory
- 8 MB flash, 8 MB PSRAM (OPI)
- Input
- no touch
Key features
- 0.85-inch IPS, 128×128
- ST7735 (GC9107 on units before 2026-05-14)
- ESP32-S3-PICO-1-N8R8: 8 MB flash, 8 MB PSRAM
- BMI270 IMU and BMM150 magnetometer
- IR transmitter
- Grove port plus six GPIO pads
Specifications
| Manufacturer | M5Stack |
|---|---|
| Screen size | 0.85" |
| Resolution | 128×128 px |
| Colour depth | 16-bit |
| Display controller | ST7735 (SPI; GC9107 before 2026-05-14) |
| Display interface | SPI |
| Touch | None (screen is the button) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-PICO-1-N8R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 8 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Display controller changed from GC9107 to ST7735 on 2026-05-14. Backlight via an LP5562 LED driver on the internal I2C bus (no backlight GPIO). BMI270 IMU (0x68) with a BMM150 magnetometer behind it, IR transmitter, user button. |
| Display | 128×128 IPS: MOSI 21, SCK 15, DC 42, CS 14, RST 48 |
| Backlight | LP5562 LED driver on internal I2C (SDA 45, SCL 0) |
| Sensors | BMI270 (0x68), BMM150 via the BMI270 hub |
| IR | Transmitter on GPIO 47 |
| Ports | Grove: GPIO 2 / 1; pads: 5, 6, 7, 8, 38, 39 |
| Size | 24 × 24 × 12.9 mm, 6.8 g |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | Internal I2C SCL (IMU, backlight driver) |
| GPIO 1 | Grove port (white) |
| GPIO 2 | Grove port (yellow) |
| GPIO 5 | Bottom GPIO pad |
| GPIO 6 | Bottom GPIO pad |
| GPIO 7 | Bottom GPIO pad |
| GPIO 8 | Bottom GPIO pad |
| GPIO 14 | LCD CS |
| GPIO 15 | LCD SCK |
| GPIO 21 | LCD MOSI |
| GPIO 38 | Bottom GPIO pad |
| GPIO 39 | Bottom GPIO pad |
| GPIO 42 | LCD DC |
| GPIO 45 | Internal I2C SDA (IMU, backlight driver) |
| GPIO 47 | IR transmitter |
| GPIO 48 | LCD reset |
Source: github.com, docs.m5stack.com, docs.m5stack.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 1 | GPIO, PWM, ADC | Grove port (white) |
| GPIO 2 | GPIO, PWM, ADC | Grove port (yellow) |
| GPIO 5 | GPIO, PWM, ADC | Bottom pad |
| GPIO 6 | GPIO, PWM, ADC | Bottom pad |
| GPIO 7 | GPIO, PWM, ADC | Bottom pad |
| GPIO 8 | GPIO, PWM, ADC | Bottom pad |
| GPIO 38 | GPIO, PWM | Bottom pad |
| GPIO 39 | GPIO, PWM | Bottom pad |
- Grove port — GPIO 2, 1 · HY2.0-4P
- Bottom GPIO pads — GPIO 5, 6, 7, 8, 38, 39 · pads / 2.54 mm header
Good to know before you start
- Wiki only for now: the LCD Ultra Pro editor supports the AtomS3, not the AtomS3R.
- Check the production date. The display driver changed in May 2026.
- Brightness is an I2C command to the LP5562, not PWM on a pin.
What it is good for
- •Tiny status indicators
- •IR blasters with feedback
- •Compass and tilt widgets
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | M5AtomS3R |
|---|
Board package: M5Stack board package (Boards Manager: M5Stack)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What is the difference between the AtomS3 and the AtomS3R?
The AtomS3R has an ESP32-S3-PICO-1-N8R8 with 8 MB of PSRAM, a BMI270 IMU with a BMM150 magnetometer and an LP5562 backlight driver.
Which display controller does the AtomS3R use?
ST7735 on units made from 14 May 2026; earlier units have a GC9107.
Which pins can I use?
GPIO 1 and 2 on the Grove port and GPIO 5, 6, 7, 8, 38 and 39 on the bottom pads.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the M5Stack family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.