Waveshare · ESP32-S3 · 1.28" · 240×240
Waveshare ESP32-S3-DualEye-Touch-LCD-1.28 specifications
This page collects the pinout and hardware details of the ESP32-S3-DualEye-Touch-LCD-1.28. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Two round screens, one ESP32-S3. The DualEye board is made for animated eyes on robots, masks and plush toys, and the second display sits on a part of the PCB you can snap off and connect back with an 18-pin FPC cable, so the eyes can be spaced however your project needs.
Both 240×240 GC9A01 displays share one SPI bus (SCK 41, MOSI 42) and one DC line (GPIO 45). Each has its own chip select, reset and backlight: GPIO 47, 48 and 46 for the first, GPIO 38, 8 and 39 for the second. That means you draw to one eye at a time, which is fine at this size.
Touch uses CST816S controllers. There's an ES8311 codec and ES7210 microphone ADC with a speaker header, a battery connector with charging and an MP1605 regulator that can supply 2 A at 3.3 V. Battery voltage reads on GPIO 1.

- Screen
- 1.28" · 240×240
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- Two round 1.28-inch displays, 240×240 each
- GC9A01 controllers on a shared SPI bus
- CST816S capacitive touch
- Breakaway second display on an FPC cable
- ES8311 + ES7210 audio, speaker header
- ESP32-S3R8, 16 MB flash, 8 MB PSRAM
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.28" |
| Resolution | 240×240 px |
| Colour depth | 16-bit |
| Display controller | 2 x GC9A01 (SPI) |
| Display interface | SPI (two displays, shared bus) |
| Touch | CST816S (capacitive, I2C 0x15, one per display) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Two round 1.28-inch 240x240 displays; the second sits on a breakaway part joined by an 18-pin FPC, so the eyes can be mounted apart. ES8311 codec, ES7210 microphone ADC, speaker header, 3.7 V battery with charging, MP1605 3.3 V / 2 A regulator. Two SH1.0 14-pin connectors (programming / second display). |
| Shared SPI | SCK 41, MOSI 42, MISO 40, DC 45 |
| Display 1 | CS 47, RST 48, backlight 46 |
| Display 2 | CS 38, RST 8, backlight 39 |
| Audio | MCLK 12, SCLK 13, LRCLK 14 |
| Power | Battery charging, MP1605 3.3 V / 2 A, battery ADC on GPIO 1 |
| Connectors | Two SH1.0 14-pin, 18-pin FPC, USB-C |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-S3-DualEye-Touch-LCD-1.28, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT (LCD1 connector) |
| GPIO 1 | Battery voltage (ADC) |
| GPIO 8 | LCD2 reset |
| GPIO 12 | I2S MCLK |
| GPIO 13 | I2S SCLK |
| GPIO 14 | I2S LRCLK |
| GPIO 38 | LCD2 CS |
| GPIO 39 | LCD2 backlight |
| GPIO 40 | SPI MISO |
| GPIO 41 | SPI SCK (both displays) |
| GPIO 42 | SPI MOSI (both displays) |
| GPIO 45 | LCD DC (both displays) |
| GPIO 46 | LCD1 backlight |
| GPIO 47 | LCD1 CS |
| GPIO 48 | LCD1 reset |
Source: github.com, docs.waveshare.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Two displays aren't something the LCD Ultra Pro editor handles yet, and this board isn't in it.
- Waveshare's examples set up the I2C and SD pins in more than one way. Check the example you start from.
- Updating both eyes doubles the SPI traffic. Keep animations light.
What it is good for
- •Robot and animatronic eyes
- •Cosplay masks
- •Interactive toys
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| Flash Mode | QIO 120MHz |
| Partition Scheme | ESP SR 16M (3MB APP/7MB SPIFFS/2.9MB MODEL) |
| PSRAM | OPI PSRAM |
| Events Run On | Core 0 |
| USB Mode | Hardware CDC and JTAG |
| USB CDC On Boot | Disabled |
Board package: esp32 by Espressif Systems 3.2.0
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Can the two displays be separated?
Yes. The second display sits on a breakaway part of the PCB and connects back through an 18-pin FPC cable.
Do both displays share pins?
They share SCK, MOSI and DC. Chip select, reset and backlight are separate for each display.
Which display driver is used?
Two GC9A01 controllers, one per round 240×240 display.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Waveshare round display family
- Waveshare ESP32-C6-LCD-1.28
- Waveshare ESP32-C6-Touch-LCD-1.28
- Waveshare ESP32-S3 LCD 1.28" round
- Waveshare ESP32-S3 LCD 1.28" round (CNC metal housing)
- Waveshare ESP32-S3 Touch LCD 1.28" round
- Waveshare ESP32-S3 Touch LCD 1.28" round (CNC metal housing)
- Waveshare ESP32-C6 Touch AMOLED 1.32" round
- Waveshare ESP32-S3 Touch AMOLED 1.32" round
- Waveshare ESP32-C6 Touch AMOLED 1.43" round
- Waveshare ESP32-S3 Touch AMOLED 1.43" round
- Waveshare ESP32-S3-Touch-AMOLED-1.43C
- Waveshare ESP32-S3 Touch LCD 1.46" round
- Waveshare ESP32-S3 Touch AMOLED 1.75" round
- Waveshare ESP32-S3-Touch-AMOLED-1.75C
- Waveshare ESP32-S3 Knob Touch LCD 1.8"
- Waveshare ESP32-S3 Touch LCD 1.85" round
- Waveshare ESP32-S3 Touch LCD 1.85" Type C
- Waveshare ESP32-S3-Touch-LCD-1.85B
- Waveshare ESP32-S3 Touch LCD 2.1" round
- Waveshare ESP32-S3-Touch-LCD-2.8C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.