Waveshare · ESP32-C6 · 1.28" · 240×240

Waveshare ESP32-C6-Touch-LCD-1.28 specifications

This page collects the pinout, free GPIOs and hardware details of the ESP32-C6-Touch-LCD-1.28. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.

A round 1.28-inch screen in a CNC metal top case makes this one of the nicer-looking small boards Waveshare sells. Inside is an ESP32-C6 with 16 MB of flash, Wi-Fi 6, Bluetooth 5 and Zigbee / Thread, driving a 240×240 GC9A01A panel with a CST816S touch controller.

The sensor set is the usual round-board kit: a QMI8658 IMU and a PCF85063 real-time clock with its own SH1.0 backup-battery connector, plus an ETA6096 charger for a 3.7 V cell and a microSD slot. A 12-pin SH1.0 header brings out four GPIOs, a UART and I2C. The -B variant ships with the case and an optional frosted acrylic back.

Waveshare's interface drawing numbers only the header pins, GPIO 1, 2, 3 and 6, so the table on this page is partial. If you already know GC9A01 boards, nothing about the panel will surprise you, but the pin numbers are specific to this board.

ESP32-C6-Touch-LCD-1.28 board diagram with an example screen: 1.28" 240×240, ESP32-C6
Annotated diagram of the Waveshare ESP32-C6-Touch-LCD-1.28, drawn by LCD Ultra Pro™.
Screen
1.28" · 240×240
Chip
ESP32-C6
Memory
16 MB flash, no PSRAM
Input
capacitive touch

Key features

  • Round 1.28-inch, 240×240, GC9A01A
  • CST816S touch
  • ESP32-C6: Wi-Fi 6, Zigbee, Thread
  • QMI8658 IMU, PCF85063 RTC
  • ETA6096 charger, microSD
  • CNC metal top case

Specifications

Waveshare ESP32-C6-Touch-LCD-1.28 technical specifications
ManufacturerWaveshare
Screen size1.28"
Resolution240×240 px
Colour depth16-bit
Display controllerGC9A01A (SPI)
Display interfaceSPI
TouchCST816S (capacitive, I2C)
MicrocontrollerESP32-C6
ModuleESP32-C6
CPU clock160 MHz
Internal SRAM512 KB
PSRAMNone
Flash16 MB
Wi-FiYes
BluetoothYes
Hardware variantRound LCD, 400 cd/m². QMI8658 IMU, PCF85063 RTC with SH1.0 backup battery connector, ETA6096 charger, microSD, SH1.0 12-pin header (4 GPIOs, UART, I2C). CNC metal top case; the -B variant comes with a case. GPIO table published only as an image.
Display240×240 round, GC9A01A (SPI), 400 cd/m²
TouchCST816S
HeaderSH1.0 12-pin: 4 GPIOs, UART, I2C
Memory16 MB flash, no PSRAM
VariantsStandard and -B (with case, optional frosted back)

GPIO pinout

The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.

Waveshare ESP32-C6-Touch-LCD-1.28 GPIO pinout
GPIOFunction
GPIO 1Header GPIO
GPIO 2Header GPIO
GPIO 3Header GPIO
GPIO 6Header GPIO
GPIO 9BOOT button (also on the header)

Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.

Free GPIOs and connectors

These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.

Free GPIO pins of the Waveshare ESP32-C6-Touch-LCD-1.28
PinCapabilitiesNote
GPIO 1GPIO, PWM, ADCOn the SH1.0 12-pin header
GPIO 2GPIO, PWM, ADCOn the SH1.0 12-pin header
GPIO 3GPIO, PWM, ADCOn the SH1.0 12-pin header
GPIO 6GPIO, PWM, ADCOn the SH1.0 12-pin header
  • SH1.0 12-pin header — GPIO 1, 2, 3, 6, 9 · SH1.0 12-pin

    Also GND, 3.3 V, RESET, BOOT, UART RX / TX and I2C SCL / SDA (the on-board bus); Waveshare does not number the UART and I2C pins

Good to know before you start

  • The LCD Ultra Pro editor does not list this board yet.
  • Only the header pins are documented with GPIO numbers.
  • The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.

What it is good for

  • •Zigbee thermostat faces
  • •Round desk clocks
  • •Compact smart-home knobs

LVGL support in LCD Ultra Pro™

This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.

Arduino IDE settings

From the manufacturer's documentation (not tested by us yet)

BoardESP32C6 Dev Module
USB CDC On BootEnabled
CPU Frequency160MHz (WiFi)
Flash ModeQIO
Flash Size16MB (128Mb)
Partition Scheme16M Flash (3MB APP/9.9MB FATFS)

Board package: esp32 by Espressif Systems

Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source

Frequently asked questions

Which display driver does it use?

A GC9A01A over SPI, 240×240 round.

Does it keep time when unplugged?

It has a PCF85063 RTC with an SH1.0 connector for a backup battery.

What does the -B variant include?

The case, with an optional frosted acrylic back plate.

Sources

Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):

More in the Waveshare round display family

Tools for this board

All free tools →

Connect sensors and parts

All sensors and parts →

Last updated:

Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.

Something wrong on this page?

Tell me what you found. I check every report and fix the page.