Waveshare · ESP32-S3 · 1.85" · 360×360
Waveshare ESP32-S3-Touch-LCD-1.85B specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-Touch-LCD-1.85B. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
The B in the name means badge. This is Waveshare's round 1.85-inch board built into a CNC aluminium enclosure, with a fuel gauge for the battery and two small SH1.0 ports for UART and I2C on the outside.
The display is a 360×360 ST77916 on QSPI: clock on GPIO 40, data on 46, 45, 42 and 41, CS 21, reset 3 and a PWM backlight on GPIO 5. Touch comes from a CST816S. On the audio side there's an ES8311 codec, an ES7210 for the two microphones and speaker pads, with the amplifier switched by GPIO 9.
What sets it apart from simpler round boards is battery awareness. A BQ27220 fuel gauge reports charge level over I2C, configured in Waveshare's examples for a 500 mAh cell. A PCF85063 clock and a QMI8658 IMU share that bus, and the microSD slot is 4-bit SDMMC.

- Screen
- 1.85" · 360×360
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- Round 1.85-inch, 360×360, ST77916 (QSPI)
- CST816S capacitive touch
- BQ27220 battery fuel gauge
- ES8311 + ES7210 audio, dual microphones
- PCF85063 RTC, QMI8658 IMU
- CNC aluminium badge enclosure
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.85" |
| Resolution | 360×360 px |
| Colour depth | 16-bit |
| Display controller | ST77916 (QSPI) |
| Display interface | QSPI |
| Touch | CST816S (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Round badge in a CNC aluminium enclosure. BQ27220 fuel gauge (500 mAh battery profile), PCF85063 RTC, QMI8658 IMU, ES8311 codec and ES7210 dual-microphone ADC, speaker pads. |
| Display | 360×360, ST77916 QSPI: CLK 40, D0 46, D1 45, D2 42, D3 41, CS 21, RST 3, backlight 5 |
| Touch | CST816S, INT 4, RST 1 |
| Audio | MCLK 2, BCLK 48, LRCLK 38, DOUT 47, DIN 39, amplifier 9 |
| I2C | SDA 11, SCL 10 (SH1.0 port and on-board chips) |
| microSD | 4-bit: CLK 15, CMD 14, D0 16, D1 17, D2 12, D3 13 |
| Ports | USB-C, SH1.0 UART (43/44), SH1.0 I2C, MX1.25 battery |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-S3-Touch-LCD-1.85B, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Touch reset |
| GPIO 2 | I2S MCLK |
| GPIO 3 | LCD reset |
| GPIO 4 | Touch interrupt |
| GPIO 5 | Backlight (PWM) |
| GPIO 6 | RTC interrupt |
| GPIO 7 | GPIO port (J6) |
| GPIO 8 | GPIO port (J6) / IMU interrupt via 0R |
| GPIO 9 | Speaker amplifier enable |
| GPIO 10 | I2C SCL (touch, RTC, IMU, codecs, fuel gauge) |
| GPIO 11 | I2C SDA (touch, RTC, IMU, codecs, fuel gauge) |
| GPIO 12 | microSD D2 |
| GPIO 13 | microSD D3 |
| GPIO 14 | microSD CMD |
| GPIO 15 | microSD CLK |
| GPIO 16 | microSD D0 |
| GPIO 17 | microSD D1 |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | LCD CS |
| GPIO 38 | I2S LRCLK |
| GPIO 39 | I2S data in (microphones) |
| GPIO 40 | LCD QSPI clock |
| GPIO 41 | LCD data 3 |
| GPIO 42 | LCD data 2 |
| GPIO 43 | UART0 TX |
| GPIO 44 | UART0 RX |
| GPIO 45 | LCD data 1 |
| GPIO 46 | LCD data 0 |
| GPIO 47 | I2S data out (speaker) |
| GPIO 48 | I2S BCLK |
Source: github.com, docs.waveshare.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 43 | GPIO, UART_TX | UART0 TX on the SH1.0 UART port |
| GPIO 44 | GPIO, UART_RX | UART0 RX on the SH1.0 UART port |
| GPIO 7 | GPIO, PWM, ADC | On the 4-pin GPIO port (J6) |
| GPIO 8 | GPIO, PWM, ADC | On the 4-pin GPIO port (J6); wired to the IMU interrupt through a 0 Ohm resistor, remove it to use the pin |
- UART port — GPIO 43, 44 (TX, RX) · SH1.0 4-pin
- I2C port — GPIO 11, 10 (SDA, SCL) · SH1.0 4-pin
Same bus as touch, RTC, IMU, codecs and fuel gauge; I2C only
- GPIO port — GPIO 7, 8 · SH1.0 4-pin
Also 3.3 V and GND
Good to know before you start
- The LCD Ultra Pro editor has no profile for the 1.85B yet.
- The PWR button only switches power; it has no GPIO for your code.
- UART0 on the SH1.0 port is also the console. Plan for log output there.
What it is good for
- •Conference and maker badges
- •Round smart-home controllers on battery
- •Voice gadgets with battery level display
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
What is the difference between the 1.85 and the 1.85B?
The B version is a badge with an aluminium enclosure and a BQ27220 fuel gauge. Compare the pin tables before reusing code from the plain 1.85.
Which display driver does it use?
An ST77916 over QSPI at 360×360.
Can I read the battery level?
Yes, from the BQ27220 fuel gauge on I2C (GPIO 10/11).
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare round display family
- Waveshare ESP32-C6-LCD-1.28
- Waveshare ESP32-C6-Touch-LCD-1.28
- Waveshare ESP32-S3 LCD 1.28" round
- Waveshare ESP32-S3 LCD 1.28" round (CNC metal housing)
- Waveshare ESP32-S3 Touch LCD 1.28" round
- Waveshare ESP32-S3 Touch LCD 1.28" round (CNC metal housing)
- Waveshare ESP32-S3-DualEye-Touch-LCD-1.28
- Waveshare ESP32-C6 Touch AMOLED 1.32" round
- Waveshare ESP32-S3 Touch AMOLED 1.32" round
- Waveshare ESP32-C6 Touch AMOLED 1.43" round
- Waveshare ESP32-S3 Touch AMOLED 1.43" round
- Waveshare ESP32-S3-Touch-AMOLED-1.43C
- Waveshare ESP32-S3 Touch LCD 1.46" round
- Waveshare ESP32-S3 Touch AMOLED 1.75" round
- Waveshare ESP32-S3-Touch-AMOLED-1.75C
- Waveshare ESP32-S3 Knob Touch LCD 1.8"
- Waveshare ESP32-S3 Touch LCD 1.85" round
- Waveshare ESP32-S3 Touch LCD 1.85" Type C
- Waveshare ESP32-S3 Touch LCD 2.1" round
- Waveshare ESP32-S3-Touch-LCD-2.8C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.