Waveshare · ESP32-C6 · 1.28" · 240×240

Waveshare ESP32-C6-LCD-1.28 specifications

This page collects the pinout, free GPIOs and hardware details of the ESP32-C6-LCD-1.28. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.

No touch, more pins. The ESP32-C6-LCD-1.28 is the round 240×240 GC9A01A board without the touch layer, and in exchange its SH1.0 14-pin header brings out six GPIOs, a UART and I2C, two GPIOs more than the touch model gets.

The rest is close to the touch version: an ESP32-C6 with 16 MB of external flash and Wi-Fi 6, Bluetooth 5 and Zigbee / Thread, a QMI8658 IMU, a PCF85063 clock with its own backup-battery connector, an ETA6096 charger for a 3.7 V cell and a microSD slot. The panel is rated at 400 cd/m².

Without touch you'll want another input: the IMU for tilt and tap, the BOOT button, or a rotary encoder on the header. The header pins in the table come from Waveshare's interface drawing: GPIO 1, 2, 3, 4, 6 and 23 are free.

ESP32-C6-LCD-1.28 board diagram with an example screen: 1.28" 240×240, ESP32-C6
Annotated diagram of the Waveshare ESP32-C6-LCD-1.28, drawn by LCD Ultra Pro™.
Screen
1.28" · 240×240
Chip
ESP32-C6
Memory
16 MB flash, no PSRAM
Input
no touch

Key features

  • Round 1.28-inch, 240×240, GC9A01A
  • No touch
  • ESP32-C6, 16 MB flash
  • QMI8658 IMU, PCF85063 RTC
  • SH1.0 14-pin header (6 GPIOs)
  • Battery charging, microSD

Specifications

Waveshare ESP32-C6-LCD-1.28 technical specifications
ManufacturerWaveshare
Screen size1.28"
Resolution240×240 px
Colour depth16-bit
Display controllerGC9A01A (SPI)
Display interfaceSPI
TouchNone
MicrocontrollerESP32-C6
ModuleESP32-C6
CPU clock160 MHz
Internal SRAM512 KB
PSRAMNone
Flash16 MB
Wi-FiYes
BluetoothYes
Hardware variantRound LCD, 400 cd/m². QMI8658 IMU, PCF85063 RTC with backup battery connector, ETA6096 charger, microSD, SH1.0 14-pin header (6 GPIOs, UART, I2C). GPIO table published only as an image.
Display240×240 round, GC9A01A (SPI), 400 cd/m²
HeaderSH1.0 14-pin: 6 GPIOs, UART, I2C
SensorsQMI8658 IMU, PCF85063 RTC
PowerETA6096 charger, MX1.25 battery, SH1.0 RTC battery
Memory16 MB flash, no PSRAM

GPIO pinout

The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.

Waveshare ESP32-C6-LCD-1.28 GPIO pinout
GPIOFunction
GPIO 1Header GPIO
GPIO 2Header GPIO
GPIO 3Header GPIO
GPIO 4Header GPIO
GPIO 6Header GPIO
GPIO 9BOOT button (also on the header)
GPIO 23Header GPIO

Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.

Free GPIOs and connectors

These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.

Free GPIO pins of the Waveshare ESP32-C6-LCD-1.28
PinCapabilitiesNote
GPIO 1GPIO, PWM, ADCOn the SH1.0 14-pin header
GPIO 2GPIO, PWM, ADCOn the SH1.0 14-pin header
GPIO 3GPIO, PWM, ADCOn the SH1.0 14-pin header
GPIO 4GPIO, PWM, ADCOn the SH1.0 14-pin header
GPIO 6GPIO, PWM, ADCOn the SH1.0 14-pin header
GPIO 23GPIO, PWMOn the SH1.0 14-pin header
  • SH1.0 14-pin header — GPIO 1, 2, 3, 4, 6, 23, 9 · SH1.0 14-pin

    Also 3.3 V, GND, UART RX / TX, RESET, BOOT and I2C SCL / SDA (the on-board bus); Waveshare does not number the UART and I2C pins

Good to know before you start

  • Not in the LCD Ultra Pro editor yet.
  • No touch input: plan buttons, IMU or an encoder.
  • Waveshare labels the header's UART and I2C pins without GPIO numbers.

What it is good for

  • •Round gauges and clocks
  • •Zigbee status displays
  • •Projects with an external encoder

LVGL support in LCD Ultra Pro™

This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.

Arduino IDE settings

From the manufacturer's documentation (not tested by us yet)

BoardESP32C6 Dev Module
USB CDC On BootEnabled
CPU Frequency160MHz (WiFi)
Flash ModeQIO
Flash Size16MB (128Mb)
Partition Scheme16M Flash (3MB APP/9.9MB FATFS)

Board package: esp32 by Espressif Systems

Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source

Frequently asked questions

Does the ESP32-C6-LCD-1.28 have touch?

No. The touch model is the ESP32-C6-Touch-LCD-1.28.

How many GPIOs are on the header?

Six GPIOs, plus a UART and I2C, on an SH1.0 14-pin header.

Which display controller does it use?

A GC9A01A over SPI.

Sources

Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):

More in the Waveshare round display family

Tools for this board

All free tools →

Connect sensors and parts

All sensors and parts →

Last updated:

Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.

Something wrong on this page?

Tell me what you found. I check every report and fix the page.