Waveshare · ESP32-S3 · 1.75" · 466×466
Waveshare ESP32-S3-Touch-AMOLED-1.75C specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-Touch-AMOLED-1.75C. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
The C matters. Waveshare already sold an ESP32-S3-Touch-AMOLED-1.75, and the 1.75C keeps the round 466×466 panel but changes enough underneath that code for one won't run on the other without edits.
The display is a CO5300 on QSPI, with data on GPIO 4 to 7, clock on 38, CS on 12 and reset on 1. Touch is a CST9217, a chip you won't find on many other boards, with its interrupt on GPIO 11 and reset on GPIO 2. Flash grows to 32 MB, next to 8 MB of PSRAM.
Audio follows Waveshare's usual pair: an ES8311 codec for the speaker, an ES7210 for two digital microphones, and an amplifier switched by GPIO 46. An AXP2101 handles battery charging and power rails, and a QMI8658 IMU sits on the same I2C bus at GPIO 14/15. Round AMOLED plus microphones makes it a natural voice-assistant face.

- Screen
- 1.75" · 466×466
- Chip
- ESP32-S3
- Memory
- 32 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- Round 1.75-inch AMOLED, 466×466
- CO5300 over QSPI, CST9217 touch
- ESP32-S3: 32 MB flash, 8 MB PSRAM
- Two digital microphones (ES7210) and ES8311 codec
- AXP2101 power management
- QMI8658 six-axis IMU
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.75" |
| Resolution | 466×466 px |
| Colour depth | 16-bit |
| Display controller | CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | CST9217 (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 32 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Round 466x466 AMOLED. Not the same board as the ESP32-S3-Touch-AMOLED-1.75 (different touch chip, memory and pins). AXP2101 PMU, QMI8658 IMU, ES8311 codec, ES7210 ADC with two digital microphones. |
| Display | 466×466 AMOLED, CO5300: D0-D3 GPIO 4 to 7, CLK 38, CS 12, RST 1 |
| Touch | CST9217, INT 11, RST 2 |
| Audio | MCLK 16, SCLK 9, LRCLK 45, DOUT 8, DIN 10, amplifier 46 |
| I2C | SDA 15, SCL 14: touch, PMU, IMU, codecs |
| Power | AXP2101 with lithium charging |
| Memory | 32 MB flash, 8 MB PSRAM |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 1 | LCD reset |
| GPIO 2 | Touch reset |
| GPIO 3 | PWR button sense (SYS_OUT) |
| GPIO 4 | LCD data 0 |
| GPIO 5 | LCD data 1 |
| GPIO 6 | LCD data 2 |
| GPIO 7 | LCD data 3 |
| GPIO 8 | I2S data out (ES8311) |
| GPIO 9 | I2S SCLK |
| GPIO 10 | I2S data in (ES7210) |
| GPIO 11 | Touch interrupt |
| GPIO 12 | LCD CS |
| GPIO 13 | LCD tearing effect (TE) |
| GPIO 14 | I2C SCL (touch, PMU, IMU, codecs) |
| GPIO 15 | I2C SDA (touch, PMU, IMU, codecs) |
| GPIO 16 | I2S MCLK |
| GPIO 17 | Header GPIO |
| GPIO 18 | Header GPIO |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | IMU interrupt |
| GPIO 38 | LCD QSPI clock |
| GPIO 39 | Header GPIO |
| GPIO 40 | Header GPIO |
| GPIO 41 | Header GPIO |
| GPIO 42 | Header GPIO |
| GPIO 43 | UART0 TX (header) |
| GPIO 44 | UART0 RX (header) |
| GPIO 45 | I2S LRCLK |
| GPIO 46 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com, github.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 17 | GPIO, PWM, ADC | On the OUT header |
| GPIO 18 | GPIO, PWM, ADC | On the OUT header |
| GPIO 39 | GPIO, PWM | On the OUT header |
| GPIO 40 | GPIO, PWM | On the OUT header |
| GPIO 41 | GPIO, PWM | On the OUT header |
| GPIO 42 | GPIO, PWM | On the OUT header |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the OUT header |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the OUT header |
- OUT header — GPIO 14, 15, 17, 18, 39, 40, 41, 42, 43, 44 · pin header pads
GPIO 14 / 15 are the on-board I2C bus (SCL / SDA)
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- Don't mix it up with the AMOLED-1.75 (without C): different touch chip and pins.
- Check that your touch library supports the CST9217.
What it is good for
- •Round voice-assistant faces
- •Smart-home knobs and remotes
- •AMOLED watch prototypes
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 32MB (256Mb) |
| Partition Scheme | 32M Flash (4.8MB APP/22MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What is the difference between the AMOLED-1.75 and the 1.75C?
Both have a round 466×466 AMOLED, but the 1.75C uses a CST9217 touch controller, 32 MB of flash and a different pin map.
Does it have microphones?
Yes, two digital microphones through an ES7210 ADC, plus an ES8311 codec for the speaker.
Is there a backlight pin?
No. It is an AMOLED panel; brightness is set with a display command.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/waveshareteam/ESP32-S3-Touch-AMOLED-1.75C
- https://github.com/waveshareteam/Waveshare-ESP32-components
- https://www.waveshare.com/esp32-s3-touch-amoled-1.75c.htm
- https://docs.waveshare.com/ESP32-S3-Touch-AMOLED-1.75C
- https://github.com/waveshareteam/ESP32-S3-Touch-AMOLED-1.75C/blob/main/hardware/schematic/ESP32-S3-Touch-AMOLED-1.75C-schematic.pdf
- https://docs.waveshare.com/ESP32-S3-Touch-AMOLED-1.75C/Arduino
More in the Waveshare round display family
- Waveshare ESP32-C6-LCD-1.28
- Waveshare ESP32-C6-Touch-LCD-1.28
- Waveshare ESP32-S3 LCD 1.28" round
- Waveshare ESP32-S3 LCD 1.28" round (CNC metal housing)
- Waveshare ESP32-S3 Touch LCD 1.28" round
- Waveshare ESP32-S3 Touch LCD 1.28" round (CNC metal housing)
- Waveshare ESP32-S3-DualEye-Touch-LCD-1.28
- Waveshare ESP32-C6 Touch AMOLED 1.32" round
- Waveshare ESP32-S3 Touch AMOLED 1.32" round
- Waveshare ESP32-C6 Touch AMOLED 1.43" round
- Waveshare ESP32-S3 Touch AMOLED 1.43" round
- Waveshare ESP32-S3-Touch-AMOLED-1.43C
- Waveshare ESP32-S3 Touch LCD 1.46" round
- Waveshare ESP32-S3 Touch AMOLED 1.75" round
- Waveshare ESP32-S3 Knob Touch LCD 1.8"
- Waveshare ESP32-S3 Touch LCD 1.85" round
- Waveshare ESP32-S3 Touch LCD 1.85" Type C
- Waveshare ESP32-S3-Touch-LCD-1.85B
- Waveshare ESP32-S3 Touch LCD 2.1" round
- Waveshare ESP32-S3-Touch-LCD-2.8C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.